Mercurial > brewboard / changelog

Changed PWM power calculation during PID use.

• Wed, 28 Jul 2021 17:12:00 +0200
• by Michiel Broek <mbroek@mbse.eu> [Wed, 28 Jul 2021 17:12:00 +0200] rev 110
• Changed PWM power calculation during PID use.

Version 0.3.17. Made the Hendi PWM change official.

• Sun, 18 Jul 2021 11:25:55 +0200
• by Michiel Broek <mbroek@mbse.eu> [Sun, 18 Jul 2021 11:25:55 +0200] rev 109
• Version 0.3.17. Made the Hendi PWM change official.

Inverted PWM signal for the Hendi.

• Sat, 17 Jul 2021 20:21:02 +0200
• by Michiel Broek <mbroek@mbse.eu> [Sat, 17 Jul 2021 20:21:02 +0200] rev 108
• Inverted PWM signal for the Hendi.

Versie 0.3.16

• Mon, 05 Jul 2021 10:31:38 +0200
• by Michiel Broek <mbroek@mbse.eu> [Mon, 05 Jul 2021 10:31:38 +0200] rev 107
• Versie 0.3.16

Schema aangepast voor pullup weerstanden voor de SD kaart. Code verbeteringen in task_sdcard.

• Mon, 05 Jul 2021 10:30:05 +0200
• by Michiel Broek <mbroek@mbse.eu> [Mon, 05 Jul 2021 10:30:05 +0200] rev 106
• Schema aangepast voor pullup weerstanden voor de SD kaart. Code verbeteringen in task_sdcard.

SD card completly switched to the SPI driver API.

• Thu, 01 Jul 2021 20:26:45 +0200
• by Michiel Broek <mbroek@mbse.eu> [Thu, 01 Jul 2021 20:26:45 +0200] rev 105
• SD card completly switched to the SPI driver API.

Version 0.3.15. Back to real sensors. During cooling the target temperature is changed in 0.5 degrees steps instead of whole degrees.

• Tue, 22 Jun 2021 23:06:41 +0200
• by Michiel Broek <mbroek@mbse.eu> [Tue, 22 Jun 2021 23:06:41 +0200] rev 104
• Version 0.3.15. Back to real sensors. During cooling the target temperature is changed in 0.5 degrees steps instead of whole degrees.

Default equipment max_watt set to 2750. Added defaults for new equipment record. Switched PWM timer to high-speed. Implemented the safety timer to prevent the MLT + HLT will draw too much power in shared mode. Removed some code ideas that were not used. The fake heater now uses the faked PWM power.

• Tue, 22 Jun 2021 22:21:09 +0200
• by Michiel Broek <mbroek@mbse.eu> [Tue, 22 Jun 2021 22:21:09 +0200] rev 103
• Default equipment max_watt set to 2750. Added defaults for new equipment record. Switched PWM timer to high-speed. Implemented the safety timer to prevent the MLT + HLT will draw too much power in shared mode. Removed some code ideas that were not used. The fake heater now uses the faked PWM power.

Finished experimental code to drive the German HendiControl board. Added BoilPower and RampPower buttons during the while boil process. RampPower (going to boil power) is now adjustable. Added PWM driver code to the driver task.

• Mon, 21 Jun 2021 19:04:10 +0200
• by Michiel Broek <mbroek@mbse.eu> [Mon, 21 Jun 2021 19:04:10 +0200] rev 102
• Finished experimental code to drive the German HendiControl board. Added BoilPower and RampPower buttons during the while boil process. RampPower (going to boil power) is now adjustable. Added PWM driver code to the driver task.

Fixed HendiControl interface connecter to match the board input. Tested the new circuit.

• Sat, 19 Jun 2021 20:46:42 +0200
• by Michiel Broek <mbroek@mbse.eu> [Sat, 19 Jun 2021 20:46:42 +0200] rev 101
• Fixed HendiControl interface connecter to match the board input. Tested the new circuit.