tip/components/u8g2/csrc/u8x8_d_sbn1661.c

/*

  u8x8_d_sbn1661.c 
  
  SED1520 / SBN1661 122x32 5V LCD
  
  Universal 8bit Graphics Library (https://github.com/olikraus/u8g2/)

  Copyright (c) 2016, olikraus@gmail.com
  All rights reserved.

  Redistribution and use in source and binary forms, with or without modification, 
  are permitted provided that the following conditions are met:

  * Redistributions of source code must retain the above copyright notice, this list 
    of conditions and the following disclaimer.
    
  * Redistributions in binary form must reproduce the above copyright notice, this 
    list of conditions and the following disclaimer in the documentation and/or other 
    materials provided with the distribution.

  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND 
  CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, 
  INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 
  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 
  DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR 
  CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 
  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 
  NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 
  LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 
  CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 
  STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 
  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF 
  ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  

  
*/
#include "u8x8.h"


static const uint8_t u8x8_d_sbn1661_init_seq[] = {
  U8X8_C(0x0c0),		                /* display start at line 0  */  
  U8X8_C(0x0a0),		                /* a0: ADC forward, a1: ADC reverse */  
  U8X8_C(0x0a4),		                /* a4: normal driving, a5: power save */  
  U8X8_C(0x0a9),		                /* a8: 1/16, a9: 1/32 duty */  

  //U8X8_C(0x0af),				/* display on */
  
  U8X8_END()             			/* end of sequence */
};

static const uint8_t u8x8_d_sbn1661_powersave0_seq[] = {
  U8X8_C(0x0af),		                /* display on */
  U8X8_END()             			/* end of sequence */
};

static const uint8_t u8x8_d_sbn1661_powersave1_seq[] = {
  U8X8_C(0x0ae),		                /* display off */
  U8X8_END()             			/* end of sequence */
};


struct u8x8_sbn1661_vars
{
  uint8_t *ptr;
  uint8_t x;
  uint8_t c;
  uint8_t arg_int;
};

#ifdef NOT_USED
static void u8x8_sbn1661_out(u8x8_t *u8x8, struct u8x8_sbn1661_vars *v, void *arg_ptr)
{
  uint8_t cnt;
  u8x8_cad_SendCmd(u8x8, 0x000 | ((v->x << 3) & 63) );
  u8x8_cad_SendCmd(u8x8, 0x0b8 | (((u8x8_tile_t *)arg_ptr)->y_pos));
  
  while( v->arg_int > 0 )
  {
      /* calculate tiles to next boundary (end or chip limit) */
      cnt = v->x;
      cnt += 8;
      cnt &= 0x0f8;
      cnt -= v->x;
            
      if ( cnt > v->c )
	cnt = v->c;
    
      /* of course we still could use cnt=1 here... */
      /* but setting cnt to 1 is not very efficient */
      //cnt = 1;
    
      v->x +=cnt;
      v->c-=cnt;
      cnt<<=3;
      u8x8_cad_SendData(u8x8, cnt, v->ptr);	/* note: SendData can not handle more than 255 bytes */    
      v->ptr += cnt;
    
      if ( v->c == 0 )
      {
	v->ptr = ((u8x8_tile_t *)arg_ptr)->tile_ptr;
	v->c = ((u8x8_tile_t *)arg_ptr)->cnt;
	v->arg_int--;
      }
      if ( ((v->x) & 7) == 0 )
	break;       
  } 
}
#endif /* NOT_USED */


static const u8x8_display_info_t u8x8_sbn1661_122x32_display_info =
{
  /* chip_enable_level = */ 0,		/* sbn1661: Not used */
  /* chip_disable_level = */ 1,		/* sbn1661: Not used */
  
  /* post_chip_enable_wait_ns = */ 100,
  /* pre_chip_disable_wait_ns = */ 20,
  /* reset_pulse_width_ms = */ 1, 
  /* post_reset_wait_ms = */ 6, 		/*  */
  /* sda_setup_time_ns = */ 12,		
  /* sck_pulse_width_ns = */ 75,	/* sbn1661: Not used */
  /* sck_clock_hz = */ 4000000UL,	/* sbn1661: Not used */
  /* spi_mode = */ 0,				/* active high, rising edge */
  /* i2c_bus_clock_100kHz = */ 4,	/* sbn1661: Not used */
  /* data_setup_time_ns = */ 200,
  /* write_pulse_width_ns = */ 200,	/*  */
  /* tile_width = */ 16,		/* width of 16*8=128 pixel */
  /* tile_hight = */ 4,
  /* default_x_offset = */ 0,
  /* flipmode_x_offset = */ 0,
  /* pixel_width = */ 122,
  /* pixel_height = */ 32
};

uint8_t u8x8_d_sbn1661_122x32(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
  uint8_t *ptr;
  //uint8_t x;
  //uint8_t c;
  
  switch(msg)
  {
    case U8X8_MSG_DISPLAY_SETUP_MEMORY:
      u8x8_d_helper_display_setup_memory(u8x8, &u8x8_sbn1661_122x32_display_info);
      break;
    case U8X8_MSG_DISPLAY_INIT:
      u8x8_d_helper_display_init(u8x8);
    
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 0, NULL);
      u8x8_cad_SendSequence(u8x8, u8x8_d_sbn1661_init_seq);
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 0, NULL);
    
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 1, NULL);
      u8x8_cad_SendSequence(u8x8, u8x8_d_sbn1661_init_seq);
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 1, NULL);
      break;
    case U8X8_MSG_DISPLAY_SET_POWER_SAVE:
      
      if ( arg_int == 0 )
      {
	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 0, NULL);
	u8x8_cad_SendSequence(u8x8, u8x8_d_sbn1661_powersave0_seq);
	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 0, NULL);

	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 1, NULL);
	u8x8_cad_SendSequence(u8x8, u8x8_d_sbn1661_powersave0_seq);
	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 1, NULL);	
      }
      else
      {
	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 0, NULL);
	u8x8_cad_SendSequence(u8x8, u8x8_d_sbn1661_powersave1_seq);
	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 0, NULL);
	
	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 1, NULL);
	u8x8_cad_SendSequence(u8x8, u8x8_d_sbn1661_powersave1_seq);
	u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 1, NULL);
	
      }
      break;
    case U8X8_MSG_DISPLAY_DRAW_TILE:

      ptr = ((u8x8_tile_t *)arg_ptr)->tile_ptr;
      // x and c are ignored (u8g2 only)
      //x = ((u8x8_tile_t *)arg_ptr)->x_pos;
      //c = ((u8x8_tile_t *)arg_ptr)->cnt;
      
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 0, NULL);
      u8x8_cad_SendCmd(u8x8, 0x000 | 0);		// column 0
      u8x8_cad_SendCmd(u8x8, 0x0b8 | (((u8x8_tile_t *)arg_ptr)->y_pos));
      u8x8_cad_SendData(u8x8, 61, ptr);	/* note: SendData can not handle more than 255 bytes */    
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 0, NULL);

      ptr += 61;
      
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_START_TRANSFER, 1, NULL);
      u8x8_cad_SendCmd(u8x8, 0x000 | 0);		// column 0
      u8x8_cad_SendCmd(u8x8, 0x0b8 | (((u8x8_tile_t *)arg_ptr)->y_pos));
    
      u8x8_cad_SendData(u8x8, 61, ptr);	/* note: SendData can not handle more than 255 bytes */    
      u8x8->cad_cb(u8x8, U8X8_MSG_CAD_END_TRANSFER, 1, NULL);
    
      break;
    default:
      return 0;
  }
  return 1;
}

uint8_t u8x8_d_sed1520_122x32(u8x8_t *u8x8, uint8_t msg, uint8_t arg_int, void *arg_ptr)
{
  return u8x8_d_sbn1661_122x32(u8x8, msg, arg_int, arg_ptr);

}