Mercurial > iotbalkon / file revision

/*
 * Copyright (c) 2017 Andrej Krutak <dev@andree.sk>
 * Copyright (c) 2018 Ruslan V. Uss <unclerus@gmail.com>
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 * 3. Neither the name of the copyright holder nor the names of itscontributors
 *    may be used to endorse or promote products derived from this software without
 *    specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

/**
 * @file bh1750.h
 *
 * @defgroup bh1750 bh1750
 * @{
 *
 * ESP-IDF driver for BH1750 light sensor
 *
 * Datasheet: ROHM Semiconductor bh1750fvi-e.pdf
 *
 * Ported from esp-open-rtos
 *
 * Copyright (c) 2017 Andrej Krutak <dev@andree.sk>\n
 * Copyright (c) 2018 Ruslan V. Uss <unclerus@gmail.com>
 *
 * BSD Licensed as described in the file LICENSE
 */
#ifndef __BH1750_H__
#define __BH1750_H__

#include <stdint.h>
#include <i2cdev.h>
#include <esp_err.h>

#ifdef __cplusplus
extern "C" {
#endif

#define BH1750_ADDR_LO 0x23 //!< I2C address when ADDR pin floating/low
#define BH1750_ADDR_HI 0x5c //!< I2C address when ADDR pin high

/**
 * Measurement mode
 */
typedef enum
{
    BH1750_MODE_ONE_TIME = 0, //!< One time measurement
    BH1750_MODE_CONTINUOUS    //!< Continuous measurement
} bh1750_mode_t;

/**
 * Measurement resolution
 */
typedef enum
{
    BH1750_RES_LOW = 0,  //!< 4 lx resolution, measurement time is usually 16 ms
    BH1750_RES_HIGH,     //!< 1 lx resolution, measurement time is usually 120 ms
    BH1750_RES_HIGH2     //!< 0.5 lx resolution, measurement time is usually 120 ms
} bh1750_resolution_t;

/**
 * @brief Initialize device descriptor
 *
 * @param[out] dev Device descriptor
 * @param[in] addr I2C address, ::BH1750_ADDR_LO or ::BH1750_ADDR_HI
 * @param[in] port I2C port number
 * @param[in] sda_gpio GPIO pin number for SDA
 * @param[in] scl_gpio GPIO pin number for SCL
 * @return `ESP_OK` on success
 */
esp_err_t bh1750_init_desc(i2c_dev_t *dev, uint8_t addr, i2c_port_t port, gpio_num_t sda_gpio, gpio_num_t scl_gpio);

/**
 * @brief Free device descriptor
 *
 * @param dev Pointer to device descriptor
 * @return `ESP_OK` on success
 */
esp_err_t bh1750_free_desc(i2c_dev_t *dev);

/**
 * @brief Power down device
 *
 * @param dev Pointer to device descriptor
 * @return `ESP_OK` on success
 */
esp_err_t bh1750_power_down(i2c_dev_t *dev);

/**
 * @brief Power on device
 *
 * @param dev Pointer to device descriptor
 * @return `ESP_OK` on success
 */
esp_err_t bh1750_power_on(i2c_dev_t *dev);

/**
 * @brief Setup device parameters
 *
 * @param dev Pointer to device descriptor
 * @param mode Measurement mode
 * @param resolution Measurement resolution
 * @return `ESP_OK` on success
 */
esp_err_t bh1750_setup(i2c_dev_t *dev, bh1750_mode_t mode, bh1750_resolution_t resolution);

/**
 * @brief Set measurement time
 *
 * @param dev Pointer to device descriptor
 * @param time Measurement time (see datasheet)
 * @return `ESP_OK` on success
 */
esp_err_t bh1750_set_measurement_time(i2c_dev_t *dev, uint8_t time);

/**
 * @brief Read LUX value from the device.
 *
 * @param dev Pointer to device descriptor
 * @param[out] level read value in lux units
 * @return `ESP_OK` on success
 */
esp_err_t bh1750_read(i2c_dev_t *dev, uint16_t *level);

#ifdef __cplusplus
}
#endif

/**@}*/

#endif /* __BH1750_H__ */