--- a/brewco/devices.c Thu Feb 25 22:42:54 2016 +0100
+++ /dev/null Thu Jan 01 00:00:00 1970 +0000
@@ -1,848 +0,0 @@
-/*****************************************************************************
- * Copyright (C) 2014..2015
- *
- * Michiel Broek <mbroek at mbse dot eu>
- *
- * This file is part of the mbsePi-apps
- *
- * This is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2, or (at your option) any
- * later version.
- *
- * mbsePi-apps is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with thermferm; see the file COPYING. If not, write to the Free
- * Software Foundation, 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
- *****************************************************************************/
-
-#include "brewco.h"
-#include "devices.h"
-#include "util.h"
-#include "xutil.h"
-#include "keyboard.h"
-#include "slcd.h"
-
-
-extern int debug;
-extern sys_config Config;
-extern int my_shutdown;
-extern uint16_t leds;
-extern int slcdHandle;
-
-#ifdef USE_SIMULATOR
-
-extern int SIM_hlt_value;
-extern int SIM_mlt_value;
-
-#endif
-
-
-
-/*
- * Read one byte from a 1-wire device like a DS2413
- */
-int read_w1(char *address, char *file)
-{
- char *addr = NULL;
- int fn = -1, rc = -1, retries = 5;
- uint8_t val;
-
- addr = xstrcpy((char *)"/sys/bus/w1/devices/");
- addr = xstrcat(addr, address);
- addr = xstrcat(addr, (char *)"/");
- addr = xstrcat(addr, file);
-
- if ((fn = open(addr, O_RDONLY)) >= 0) {
-
- if ((lseek(fn, 0L, SEEK_SET)) == 0) {
-
- while (retries--) {
- if ((read(fn, &val, 1)) == 1) {
- rc = (int)val;
- goto leave;
- }
- }
- syslog(LOG_NOTICE, "read_w1() read %s fatal: %s", addr, strerror(errno));
-
- } else {
- syslog(LOG_NOTICE, "read_w1() lseek %s: %s", addr, strerror(errno));
- }
-
- } else {
- syslog(LOG_NOTICE, "read_w1() open %s: %s", addr, strerror(errno));
- }
-
-leave:
- if (fn != -1) {
- if ((close(fn)) == -1) {
- syslog(LOG_NOTICE, "read_w1() close %s: %s", addr, strerror(errno));
- }
- }
-
- free(addr);
- return rc;
-}
-
-
-
-/*
- * Write a byte to a 1-wire device like a DS2413
- */
-int write_w1(char *address, char *file, uint8_t val)
-{
- char *addr = NULL;
- int fn = -1, rc = -1, retries = 5;
-
- addr = xstrcpy((char *)"/sys/bus/w1/devices/");
- addr = xstrcat(addr, address);
- addr = xstrcat(addr, (char *)"/");
- addr = xstrcat(addr, file);
-
- if ((fn = open(addr, O_WRONLY)) >= 0) {
-
- if ((lseek(fn, 0L, SEEK_SET)) == 0) {
-
- while (retries--) {
- if ((write(fn, &val, 1)) == 1) {
- rc = 0;
- goto leave;
- }
- }
- syslog(LOG_NOTICE, "write_w1() write %s fatal: %s", addr, strerror(errno));
-
- } else {
- syslog(LOG_NOTICE, "write_w1() lseek %s: %s", addr, strerror(errno));
- }
-
- } else {
- syslog(LOG_NOTICE, "write_w1() open %s: %s", addr, strerror(errno));
- }
-
-leave:
- if (fn != -1) {
- if ((close(fn)) == -1) {
- syslog(LOG_NOTICE, "write_w1() close %s: %s", addr, strerror(errno));
- }
- }
-
- free(addr);
- return rc;
-}
-
-
-
-void hlt_heater(int value)
-{
- if (value) {
- leds |= SLED_HLTH;
- } else {
- leds &= ~SLED_HLTH;
- }
- slcdLEDs(slcdHandle);
-}
-
-
-
-void mlt_heater(int value)
-{
- if (value) {
- leds |= SLED_MLTH;
- } else {
- leds &= ~SLED_MLTH;
- }
- slcdLEDs(slcdHandle);
-}
-
-
-
-void mlt_pump(int value)
-{
- pump_status(value);
- if (value) {
- leds |= SLED_MLTP;
- } else {
- leds &= ~SLED_MLTP;
- }
- slcdLEDs(slcdHandle);
-}
-
-
-
-int device_out(char *uuid, int value)
-{
- devices_list *device;
- time_t now, my_timestamp;
- int rc, my_value, test_value;
-
- if (uuid == NULL)
- return 0;
-
- now = time(NULL);
-
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
-
- for (device = Config.devices; device; device = device->next) {
- if (! strcmp(uuid, device->uuid)) {
- /*
- * Execute command if different then the old value. But also
- * every 2 minutes because commands can have temporary
- * disconnects, or have radio problems.
- */
- my_timestamp = device->timestamp;
- my_value = device->value;
-
- if ((device->type == DEVTYPE_W1) && (device->direction == DEVDIR_OUT_BIN)) {
- test_value = (value == 0) ? 0 : 1;
- } else {
- test_value = value;
- }
-
- if ((test_value != my_value) || (((int)now - (int)my_timestamp) >= 120)) {
-
-#ifdef HAVE_WIRINGPI_H
- rc = 0;
- if ((device->type == DEVTYPE_GPIO) && (device->gpiopin != -1) && (device->present == DEVPRESENT_YES)) {
-
- }
-#endif
- if ((device->type == DEVTYPE_W1) && (device->direction == DEVDIR_OUT_BIN) && (device->present == DEVPRESENT_YES)) {
- if (strncmp(device->address, (char *)"3a", 2) == 0) {
- /*
- * DS2413. First read state so that we can preserve the state of
- * the "other" PIO channel. To make things a bit more complicated
- * the bits in the state register differ from the output register.
- */
- uint8_t state, output;
-
- if ((rc = read_w1(device->address, (char *)"state")) >= 0) {
- state = (unsigned int)rc;
- output = (state & 0x01) + ((state & 0x04) >> 1);
-
- if (device->subdevice == 0) {
- output = (output & 0xfe);
- output |= (value == 0) ? 0x01 : 0x00;
- } else if (device->subdevice == 1) {
- output = (output & 0xfd);
- output |= (value == 0) ? 0x02 : 0x00;
- } else {
- output = 0xff;
- }
-
- if ((write_w1(device->address, (char *)"output", output)) == 0) {
- syslog(LOG_NOTICE, "DS2413 PIO%c value=%d (%s)", (device->subdevice == 0) ? 'A' : 'B', (value == 0) ? 0 : 1, device->comment);
- if (debug)
- fprintf(stdout, "DS2413 PIO%c value=%d (%s)\n", (device->subdevice == 0) ? 'A' : 'B', (value == 0) ? 0 : 1, device->comment);
- device->value = (value == 0) ? 0 : 1;
- device->timestamp = time(NULL);
- }
- }
- }
- }
-
-#ifdef USE_SIMULATOR
- if ((device->type == DEVTYPE_SIM) && (device->direction == DEVDIR_OUT_BIN) && (device->present == DEVPRESENT_YES)) {
- if ((strcmp((char *)"SimHLTheater", device->address) == 0) ||
- (strcmp((char *)"SimMLTheater", device->address) == 0) ||
- (strcmp((char *)"SimMLTpump", device->address) == 0)) {
- device->value = value;
- if (strcmp((char *)"SimHLTheater", device->address) == 0) {
- SIM_hlt_value = value;
- hlt_heater(value);
- }
- if (strcmp((char *)"SimMLTheater", device->address) == 0) {
- SIM_mlt_value = value;
- mlt_heater(value);
- }
- if (strcmp((char *)"SimMLTpump", device->address) == 0) {
- mlt_pump(value);
- }
- }
- }
-#endif
- } else {
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- return 0;
- }
- }
- }
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
-
- return 0;
-}
-
-
-/*
- * Returns DEVPRESENT_NO if failed.
- * Returns DEVPRESENT_YES if success, value contains new value.
- */
-int device_in(char *uuid, int *value)
-{
- devices_list *device;
- int tmp, present;
-
- if (uuid == NULL)
- return 0;
-
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
-
- for (device = Config.devices; device; device = device->next) {
- if (! strcmp(uuid, device->uuid)) {
- present = device->present;
- if (present == DEVPRESENT_YES) {
- tmp = device->value + device->offset;
- } else {
- tmp = 0;
- }
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- *value = tmp;
- return present;
- }
- }
-
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
-
- return DEVPRESENT_NO;
-}
-
-
-
-
-/*
- * Auto detect hotplugged or known to be present devices
- */
-int devices_detect(void)
-{
- struct dirent *de;
- DIR *fd;
- devices_list *device, *ndev;
- int found, subdevices, ival, i, rc = 0;
- char buf[40];
- uuid_t uu;
-#ifdef HAVE_WIRINGPI_H
- int pin;
-#endif
-
- /*
- * Scan for 1-wire devices
- */
- if ((fd = opendir((char *)"/sys/bus/w1/devices"))) {
- while ((de = readdir(fd))) {
- if (de->d_name[0] != '.') {
- found = FALSE;
- for (device = Config.devices; device; device = device->next) {
- if (strcmp(device->address,de->d_name) == 0) {
- found = TRUE;
- break;
- }
- }
-
- if (found == FALSE) {
- strncpy(buf, de->d_name, 2);
- buf[2] = '\0';
- sscanf(buf, "%02x", &ival);
- syslog(LOG_NOTICE, "Scan 1-wire %02x %d", ival, ival);
- subdevices = 1;
- if (strcmp(buf, (char *)"29") == 0)
- subdevices = 8;
- if (strcmp(buf, (char *)"3a") == 0)
- subdevices = 2;
- for (i = 0; i < subdevices; i++) {
- ndev = (devices_list *)malloc(sizeof(devices_list));
- ndev->next = NULL;
- ndev->version = 1;
- ndev->uuid = malloc(37);
- uuid_generate(uu);
- uuid_unparse(uu, ndev->uuid);
- ndev->type = DEVTYPE_W1;
- ndev->direction = DEVDIR_UNDEF;
- if (strcmp(buf, (char *)"10") == 0) {
- ndev->direction = DEVDIR_IN_ANALOG;
- ndev->description = xstrcpy((char *)"DS18S20 Digital thermometer");
- } else if (strcmp(buf, (char *)"22") == 0) {
- ndev->direction = DEVDIR_IN_ANALOG;
- ndev->description = xstrcpy((char *)"DS1820 Digital thermometer");
- } else if (strcmp(buf, (char *)"28") == 0) {
- ndev->direction = DEVDIR_IN_ANALOG;
- ndev->description = xstrcpy((char *)"DS18B20 Digital thermometer");
- } else if (strcmp(buf, (char *)"3a") == 0) {
- ndev->description = xstrcpy((char *)"DS2413 Dual channel addressable switch");
- ndev->direction = DEVDIR_IN_BIN;
- } else if (strcmp(buf, (char *)"3b") == 0) {
- ndev->direction = DEVDIR_IN_ANALOG;
- ndev->description = xstrcpy((char *)"DS1825 Digital thermometer");
- } else if (strcmp(buf, (char *)"42") == 0) {
- ndev->direction = DEVDIR_IN_ANALOG;
- ndev->description = xstrcpy((char *)"DS28EA00 Digital thermometer");
- } else if (strcmp(buf, (char *)"w1") == 0) {
- ndev->description = xstrcpy((char *)"Master System device");
- } else {
- ndev->description = xstrcpy((char *)"Unknown device family ");
- ndev->description = xstrcat(ndev->description, buf);
- }
- ndev->value = ndev->offset = ndev->inuse = 0;
- ndev->present = DEVPRESENT_YES;
- ndev->address = xstrcpy(de->d_name);
- ndev->subdevice = i;
- ndev->gpiopin = -1;
- ndev->comment = xstrcpy((char *)"Auto detected device");
- ndev->timestamp = time(NULL);
-
- if (Config.devices == NULL) {
- Config.devices = ndev;
- } else {
- for (device = Config.devices; device; device = device->next) {
- if (device->next == NULL) {
- device->next = ndev;
- break;
- }
- }
- }
- rc++;
- }
- }
- }
- }
- closedir(fd);
- }
-
-#ifdef HAVE_WIRINGPI_H
- if (piBoardRev() == 2) {
- /*
- * Support rev B and newer boards only
- */
- found = FALSE;
- for (device = Config.devices; device; device = device->next) {
- if (device->type == DEVTYPE_GPIO) {
- found = TRUE;
- break;
- }
- }
-
- if (found == FALSE) {
- /*
- * There were no GPIO devices found.
- */
- subdevices = 12;
- pin = 0;
- for (i = 0; i < subdevices; i++) {
- if (i == 8)
- pin = 17;
-
- ndev = (devices_list *)malloc(sizeof(devices_list));
- ndev->next = NULL;
- ndev->version = 1;
- ndev->uuid = malloc(37);
- uuid_generate(uu);
- uuid_unparse(uu, ndev->uuid);
- ndev->type = DEVTYPE_GPIO;
- ndev->value = digitalRead(pin);
- ndev->offset = 0;
- ndev->present = DEVPRESENT_YES;
- ndev->address = xstrcpy((char *)"GPIO");
- snprintf(buf, 39, "Raspberry GPIO %d", i);
- ndev->description = xstrcpy(buf);
- ndev->subdevice = i;
- ndev->gpiopin = pin;
- ndev->timestamp = time(NULL);
- switch (i) {
- case 0:
- ndev->direction = DEVDIR_OUT_ANALOG;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"MLT heater SSR");
- break;
- case 1:
- ndev->direction = DEVDIR_OUT_ANALOG;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"MLT heater PWM");
- break;
- case 2:
- ndev->direction = DEVDIR_OUT_ANALOG;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"MLT pump relay");
- break;
- case PANEL_RETURN:
- ndev->direction = DEVDIR_IN_BIN;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"Frontpanel Return");
- break;
- case PANEL_ENTER:
- ndev->direction = DEVDIR_IN_BIN;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"Frontpanel Enter key");
- break;
- case PANEL_DOWN:
- ndev->direction = DEVDIR_IN_BIN;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"Frontpanel Down key");
- break;
- case PANEL_UP:
- ndev->direction = DEVDIR_IN_BIN;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"Frontpanel Up key");
- break;
- case 7:
- ndev->direction = DEVDIR_INTERN;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"1-Wire bus");
- break;
- case 8:
- ndev->direction = DEVDIR_OUT_BIN;
- ndev->inuse = 1;
- ndev->comment = xstrcpy((char *)"Buzzer");
- break;
- default:
- ndev->direction = DEVDIR_IN_BIN;
- ndev->inuse = 0;
- ndev->comment = xstrcpy((char *)"Raspberry GPIO");
- }
- pin++;
-
- if (Config.devices == NULL) {
- Config.devices = ndev;
- } else {
- for (device = Config.devices; device; device = device->next) {
- if (device->next == NULL) {
- device->next = ndev;
- break;
- }
- }
- }
- rc++;
- }
- }
- }
-#endif
-
-#ifdef USE_SIMULATOR
- found = FALSE;
- for (device = Config.devices; device; device = device->next) {
- if (device->type == DEVTYPE_SIM) {
- found = TRUE;
- break;
- }
- }
-
- if (found == FALSE) {
- subdevices = 6;
- for (i = 0; i < subdevices; i++) {
- ndev = (devices_list *)malloc(sizeof(devices_list));
- ndev->next = NULL;
- ndev->version = 1;
- ndev->uuid = malloc(37);
- uuid_generate(uu);
- uuid_unparse(uu, ndev->uuid);
- ndev->type = DEVTYPE_SIM;
- ndev->value = ndev->offset = 0;
- ndev->present = DEVPRESENT_YES;
- ndev->subdevice = i;
- ndev->gpiopin = -1;
- ndev->comment = xstrcpy((char *)"Auto detected device");
- ndev->timestamp = time(NULL);
- ndev->inuse = 0;
- switch (i) {
- case 0: ndev->direction = DEVDIR_IN_ANALOG;
- ndev->address = xstrcpy((char *)"SimRoomtemp");
- ndev->description = xstrcpy((char *)"Simulated room temperature");
- break;
- case 1: ndev->direction = DEVDIR_IN_ANALOG;
- ndev->address = xstrcpy((char *)"SimHLTtemp");
- ndev->description = xstrcpy((char *)"Simulated HLT temperature");
- break;
- case 2: ndev->direction = DEVDIR_IN_ANALOG;
- ndev->address = xstrcpy((char *)"SimMLTtemp");
- ndev->description = xstrcpy((char *)"Simulated MLT temperature");
- break;
- case 3: ndev->direction = DEVDIR_OUT_BIN;
- ndev->address = xstrcpy((char *)"SimHLTheater");
- ndev->description = xstrcpy((char *)"Simulated HLT heater");
- break;
- case 4: ndev->direction = DEVDIR_OUT_BIN;
- ndev->address = xstrcpy((char *)"SimMLTheater");
- ndev->description = xstrcpy((char *)"Simulated MLT heater");
- break;
- case 5: ndev->direction = DEVDIR_OUT_BIN;
- ndev->address = xstrcpy((char *)"SimMLTpump");
- ndev->description = xstrcpy((char *)"Simulated MLT pump");
- break;
- }
-
- if (Config.devices == NULL) {
- Config.devices = ndev;
- } else {
- for (device = Config.devices; device; device = device->next) {
- if (device->next == NULL) {
- device->next = ndev;
- break;
- }
- }
- }
- rc++;
- }
- }
-#endif
-
- return rc;
-}
-
-
-
-#ifdef HAVE_WIRINGPI_H
-PI_THREAD (my_devices_loop)
-#else
-void *my_devices_loop(void *threadid)
-#endif
-{
- devices_list *device;
- char *addr = NULL, line[60], *p = NULL;
- FILE *fp;
- int temp, rc;
-
- syslog(LOG_NOTICE, "Thread my_devices_loop started");
- if (debug)
- fprintf(stdout, "Thread my_devices_loop started\n");
-
-#ifdef HAVE_WIRINGPI_H
- if ((rc = piHiPri(10)))
- syslog(LOG_NOTICE, "my_devices_loop: piHiPri(10) rc=%d", rc);
-#endif
-
- /*
- * Loop forever until the external shutdown variable is set.
- */
- for (;;) {
-
- /*
- * Process all devices.
- */
- for (device = Config.devices; device; device = device->next) {
-
- if (my_shutdown)
- break;
-
- switch (device->type) {
- case DEVTYPE_W1:
- /*
- * Only tested with DS18B20 but from the kernel source this
- * should work with all 1-wire thermometer sensors.
- */
- if ((strncmp(device->address, (char *)"10", 2) == 0) ||
- (strncmp(device->address, (char *)"22", 2) == 0) ||
- (strncmp(device->address, (char *)"28", 2) == 0) ||
- (strncmp(device->address, (char *)"3b", 2) == 0) ||
- (strncmp(device->address, (char *)"42", 2) == 0)) {
- addr = xstrcpy((char *)"/sys/bus/w1/devices/");
- addr = xstrcat(addr, device->address);
- addr = xstrcat(addr, (char *)"/w1_slave");
- if ((fp = fopen(addr, "r"))) {
- if (device->present != DEVPRESENT_YES) {
- syslog(LOG_NOTICE, "sensor %s is back", device->address);
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- device->present = DEVPRESENT_YES;
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- }
- /*
- * The output looks like:
- * 72 01 4b 46 7f ff 0e 10 57 : crc=57 YES
- * 72 01 4b 46 7f ff 0e 10 57 t=23125
- */
- fgets(line, 50, fp);
- line[strlen(line)-1] = '\0';
- if ((line[36] == 'Y') && (line[37] == 'E')) {
- /* CRC is Ok, continue */
- fgets(line, 50, fp);
- line[strlen(line)-1] = '\0';
- strtok(line, (char *)"=");
- p = strtok(NULL, (char *)"=");
- rc = sscanf(p, "%d", &temp);
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- if ((rc == 1) && (device->value != temp)) {
- device->value = temp;
- device->timestamp = time(NULL);
- }
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- } else {
- syslog(LOG_NOTICE, "sensor %s CRC error", device->address);
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- device->present = DEVPRESENT_ERROR;
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- }
- fclose(fp);
- } else {
- if (device->present != DEVPRESENT_NO) {
- syslog(LOG_NOTICE, "sensor %s is missing", device->address);
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- device->present = DEVPRESENT_NO;
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- }
- }
- free(addr);
- addr = NULL;
- } /* if temperature sensor */
- /*
- * DS2413 Dual channel addressable switch
- */
- if (strncmp(device->address, (char *)"3a", 2) == 0) {
- addr = xstrcpy((char *)"/sys/bus/w1/devices/");
- addr = xstrcat(addr, device->address);
- addr = xstrcat(addr, (char *)"/state");
-
- if ((access(addr, R_OK)) == 0) {
- if (device->present != DEVPRESENT_YES) {
- syslog(LOG_NOTICE, "DS2413 %s is back", device->address);
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- device->present = DEVPRESENT_YES;
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- }
- /*
- * First make sure that if this device is configured as input
- * to drive the output high.
- */
- if (device->direction == DEVDIR_IN_BIN) {
- uint8_t state, output;
-
- if ((rc = read_w1(device->address, (char *)"state")) >= 0) {
- state = (unsigned int)rc;
- output = ((state & 0x02) >> 1) + ((state & 0x08) >> 2); /* Both latch states */
- if (device->subdevice == 0) {
- output = (output & 0xfe);
- output |= 0x01;
- } else if (device->subdevice == 1) {
- output = (output & 0xfd);
- output |= 0x02;
- } else {
- output = 0xff;
- }
- write_w1(device->address, (char *)"output", output);
- }
- }
- if ((rc = read_w1(device->address, (char *)"state")) >= 0) {
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- /*
- * Read PIOA or PIOB pin state bits
- */
- if (device->subdevice == 0)
- device->value = (rc & 0x01) ? 0 : 1;
- else if (device->subdevice == 1)
- device->value = (rc & 0x04) ? 0 : 1;
- device->timestamp = time(NULL);
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- }
- } else {
- if (device->present != DEVPRESENT_NO) {
- syslog(LOG_NOTICE, "DS2413 %s is missing", device->address);
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- device->present = DEVPRESENT_NO;
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- }
- }
- free(addr);
- addr = NULL;
- }
-
- break;
-
-#ifdef HAVE_WIRINGPI_H
- case DEVTYPE_GPIO:
- if (device->direction == DEVDIR_IN_BIN) {
- piLock(LOCK_DEVICES);
- device->value = digitalRead(device->gpiopin);
- device->offset = 0;
- device->timestamp = time(NULL);
- piUnlock(LOCK_DEVICES);
- }
- break;
-
-#endif
-#ifdef USE_SIMULATOR
- case DEVTYPE_SIM:
-#ifdef HAVE_WIRINGPI_H
- piLock(LOCK_DEVICES);
-#endif
- if (Config.simulator) {
- if (device->subdevice == 0) {
- device->value = (int)(Config.simulator->room_temperature * 1000);
- device->timestamp = time(NULL);
- } else if (device->subdevice == 1) {
- device->value = (int)(Config.simulator->hlt_temperature * 1000);
- device->timestamp = time(NULL);
- } else if (device->subdevice == 2) {
- device->value = (int)(Config.simulator->mlt_temperature * 1000);
- device->timestamp = time(NULL);
- }
- }
-#ifdef HAVE_WIRINGPI_H
- piUnlock(LOCK_DEVICES);
-#endif
- break;
-#endif
- default:
- break;
- }
-
- /*
- * Delay a bit after procesing a device.
- */
- usleep(10000);
- }
-
- if (my_shutdown)
- break;
- /*
- * Delay a bit after all devices
- */
- usleep(100000);
- }
-
- syslog(LOG_NOTICE, "Thread my_devices_loop stopped");
- if (debug)
- fprintf(stdout, "Thread my_devices_loop stopped\n");
- return 0;
-}
-
-
-