changelog
- Mon, 08 May 2017 16:26:02 +0200
- by Michiel Broek <mbroek@mbse.eu> [Mon, 08 May 2017 16:26:02 +0200] rev 506
- New MQTT protocol
- Sat, 29 Apr 2017 17:47:00 +0200
- by Michiel Broek <mbroek@mbse.eu> [Sat, 29 Apr 2017 17:47:00 +0200] rev 505
- Small fix
- Sat, 29 Apr 2017 17:07:36 +0200
- by Michiel Broek <mbroek@mbse.eu> [Sat, 29 Apr 2017 17:07:36 +0200] rev 504
- Added some MQTT publish clear functions. Version 0.5.8
- Thu, 12 May 2016 21:43:07 +0200
- by Michiel Broek <mbroek@mbse.eu> [Thu, 12 May 2016 21:43:07 +0200] rev 503
- Better door and 12 volt detection and logging
- Wed, 11 May 2016 14:47:27 +0200
- by Michiel Broek <mbroek@mbse.eu> [Wed, 11 May 2016 14:47:27 +0200] rev 502
- Fixed some MQTT messages. Added more profile MQTT messages. Version 0.5.7
- Mon, 09 May 2016 21:37:25 +0200
- by Michiel Broek <mbroek@mbse.eu> [Mon, 09 May 2016 21:37:25 +0200] rev 501
- Bumped to version 0.5.6
- Mon, 09 May 2016 21:35:55 +0200
- by Michiel Broek <mbroek@mbse.eu> [Mon, 09 May 2016 21:35:55 +0200] rev 500
- Units now have an unique alias name so that the MQTT messages are more friendly.
- Mon, 02 May 2016 16:15:37 +0200
- by Michiel Broek <mbroek@mbse.eu> [Mon, 02 May 2016 16:15:37 +0200] rev 499
- Created mqtt sourcefiles. Use flags to trigger publish messages. The main source does not know and does not care if MQTT messages will be sent. Version 0.5.5
- Sat, 30 Apr 2016 21:25:10 +0200
- by Michiel Broek <mbroek@mbse.eu> [Sat, 30 Apr 2016 21:25:10 +0200] rev 498
- Fixed empty setpoint values
- Sat, 30 Apr 2016 21:06:20 +0200
- by Michiel Broek <mbroek@mbse.eu> [Sat, 30 Apr 2016 21:06:20 +0200] rev 497
- Compiles mosquitto code if library is found on the system. Bumped to version 0.5.4
- Sat, 26 Mar 2016 14:43:31 +0100
- by Michiel Broek <mbroek@mbse.eu> [Sat, 26 Mar 2016 14:43:31 +0100] rev 496
- The FAN always runs if the unit is active. Bumped tp version 0.5.3
- Thu, 17 Mar 2016 23:28:29 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 17 Mar 2016 23:28:29 +0100] rev 495
- Code cleanup.
- Thu, 17 Mar 2016 17:25:02 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 17 Mar 2016 17:25:02 +0100] rev 494
- Fix Deadlok problem when there is only a heater or a cooler.
- Thu, 17 Mar 2016 17:10:41 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 17 Mar 2016 17:10:41 +0100] rev 493
- Fixed server log when changed PID parameters from the web interface.
- Fri, 11 Mar 2016 20:27:02 +0100
- by Michiel Broek <mbroek@mbse.eu> [Fri, 11 Mar 2016 20:27:02 +0100] rev 492
- Changed PID code. PID parameters are now stored 3 digits instead of 2 behind the decimal point. Prevent extreme heating or cooling in Beer mode. Heat and Cool lockdown now allows the lagest value to win instead of zero them both. PID output treshold from 2% to 50%.
- Sat, 05 Mar 2016 12:50:23 +0100
- by Michiel Broek <mbroek@mbse.eu> [Sat, 05 Mar 2016 12:50:23 +0100] rev 491
- Switched PID to BOO mode for all modes.
- Fri, 26 Feb 2016 15:14:00 +0100
- by Michiel Broek <mbroek@mbse.eu> [Fri, 26 Feb 2016 15:14:00 +0100] rev 490
- Remove temporary marker.
- Fri, 26 Feb 2016 13:38:44 +0100
- by Michiel Broek <mbroek@mbse.eu> [Fri, 26 Feb 2016 13:38:44 +0100] rev 489
- Swapped heat/cool symbols.
- Thu, 25 Feb 2016 23:24:50 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 25 Feb 2016 23:24:50 +0100] rev 488
- Small brewpanel display error fix, did not affect real hardware.
- Thu, 25 Feb 2016 23:14:46 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 25 Feb 2016 23:14:46 +0100] rev 487
- Bumped to version 0.5.2 and removed the brewco subdirectory because that has been implemented as Arduino project.
- Thu, 25 Feb 2016 22:42:54 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 25 Feb 2016 22:42:54 +0100] rev 486
- Compacted LCD display for units, allways 4 instead of 4 to 6 lines. But it's a bit more cryptic. We could write a short manual.
- Thu, 25 Feb 2016 20:26:40 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 25 Feb 2016 20:26:40 +0100] rev 485
- Fixed compiler warning
- Thu, 25 Feb 2016 20:12:27 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 25 Feb 2016 20:12:27 +0100] rev 484
- Use user defined characters for the LCD display just like in Arduino projects.
- Mon, 22 Feb 2016 19:24:49 +0100
- by Michiel Broek <mbroek@mbse.eu> [Mon, 22 Feb 2016 19:24:49 +0100] rev 483
- Merge
- Mon, 22 Feb 2016 19:22:39 +0100
- by Michiel Broek <mbroek@mbse.eu> [Mon, 22 Feb 2016 19:22:39 +0100] rev 482
- Simulate sensors resolution.
- Thu, 31 Dec 2015 21:03:52 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 31 Dec 2015 21:03:52 +0100] rev 481
- Less PID debug logging.
- Thu, 31 Dec 2015 20:52:28 +0100
- by Michiel Broek <mbroek@mbse.eu> [Thu, 31 Dec 2015 20:52:28 +0100] rev 480
- Fixed compiling on real Pi's
- Sun, 27 Dec 2015 20:52:52 +0100
- by Michiel Broek <mbroek@mbse.eu> [Sun, 27 Dec 2015 20:52:52 +0100] rev 479
- Bild target temperature 0.1 degree higher. Removed debug log from the simulator
- Sun, 27 Dec 2015 20:21:06 +0100
- by Michiel Broek <mbroek@mbse.eu> [Sun, 27 Dec 2015 20:21:06 +0100] rev 478
- The simulator now simulates the heater power in Watts. Changed Mash Remove? prompt.
- Sun, 27 Dec 2015 17:52:26 +0100
- by Michiel Broek <mbroek@mbse.eu> [Sun, 27 Dec 2015 17:52:26 +0100] rev 477
- Renamed Mash-in step to Prepare on the display. Don't run the pump when the mash is added. When preparing the mash, first heat the HLT, and then the MLT so that both have the chance to reach their target temperatures.