# HG changeset patch # User Michiel Broek # Date 1425890538 -3600 # Node ID 7ce8e4e15b0bc454629449e3239a0714db336ba4 # Parent d40a2f61b4f707996aadabcc274d9e918eb6617a Added the README diff -r d40a2f61b4f7 -r 7ce8e4e15b0b thermferm/README --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/thermferm/README Mon Mar 09 09:42:18 2015 +0100 @@ -0,0 +1,143 @@ + + 1. Introduction. + + 2. Hardware. + + 3. Raspberry GPIO. + +Most of the hardware is connected via the 8 GPIO pins on the 26p connector. +Currently the pins are used or reserved for: + + GPIO0 - out - 433 MHz transmitter module (FS1000A). + GPIO1 - out - reserved for PWM. + GPIO2 - out - Frontpanel LED. + GPIO3 - bus - DHT11 sensor. + GPIO4 - in - Frontpanel Key Enter. + GPIO5 - in - Frontpanel Key Down. + GPIO6 - in - Frontpanel Key Up. + GPIO7 - bus - 1-Wire bus (Maxim protocol). + + + 4. Keyed menu. + +Using three buttons the device can be controlled. The menu is entered by +pressing the Enter key for 2 seconds. With the up and down keys you can step +through the menu. Press escape to go back, Press enter for 2 seconds to +set the new value. +Escape is press both arrow keys together. +If not in a menu, short touch of the keys activate the LCD display backlight. +The arrow keys select the current item to display. + + + General setup + + Top screen + Units setup -- Units -- Select mode + Off mode, toggle heater, cooler, fan. + Beer/Fridge mode, change temperature. + Profile mode -- If OFF, select a profile. + If OFF, allow start profile. + If RUN, allow pause/abort. + If PAUSE, allow resume/abort. + If DONE, allow to go OFF. + System mode -- Halt + Reboot + + + + 5. Client/Server protocol. + + +Commands: + +ARCHIVE DIR +ARCHIVE LOG filename (get in LOG format) +ARCHIVE GET filename (download file) + +DEVICE ADD type +DEVICE DEL uuid +DEVICE LIST +DEVICE GET uuid +DEVICE PUT uuid + +GLOBAL GET +GLOBAL PUT + +LIST +LIST LOG uuid + +PING + +PROFILE uuid,name +PROFILE ADD name +PROFILE DEL uuid +PROFILE LIST +PROFILE GET uuid +PROFILE PUT uuid +PROFILE GETS uuid +PROFILE PUTS uuid + +SIMULATOR ADD name +SIMULATOR DEL uuid +SIMULATOR LIST +SIMULATOR GET uuid +SIMULATOR PUT uuid + +UNIT ADD name +UNIT DEL uuid +UNIT LIST +UNIT GET uuid +UNIT PUT uuid + + + +Response codes: + +100 Help text follows +101 PONG +201 Information follows +211 Device %s added +211 Device %s deleted +211 Profile %s added +211 Profile %s deleted +211 Unit %s added +211 Unit %s deleted +212 Archive directory follows: +212 Archive file follows: +212 Devices list follows: +212 Fermenter list follows: +212 Logfile list follows: +212 Profiles list follows: +213 Device record follows: +213 Global Settings record follows: +213 Profile record follows: +213 Unit listing follows: +215 Profile steps follow: +219 Accepted Device record +219 Accepted Global record +219 Accepted Profile record +219 Accepted Profile steps +219 Accepted Unit record +403 LCD not available +440 No such device +440 No such file +440 No such profile +440 No such simulator +440 No such unit +441 Maximum simulators reached +500 Unknown command +501 Subcommand missing +502 Parameter missing +503 Parameter error +504 Subcommand error +518 recfrom(): %s + + + + 6. PID adjustments. + +* Start with Kp, Kd and Ki set to 0. +* Increase Kp until small oscillation. +* Increase Kd until a little damping. +* Increase Ki after Kp and Kd are set until longterm convergence. +